Skip to main content
(215) 565-0220Mon–Fri: 8:30AM–5:30PM · Sat: 8:30AM–4PM
ABS Light On: What It Means and Is It Safe to Drive?
Brakes

ABS Light On: What It Means and Is It Safe to Drive?

November 3, 20266 min read
Written by Evan, Owner & Lead Mechanic
Back to all articles

Quick Answer

An ABS light means your anti-lock braking system has found a fault and turned itself off. Your normal brakes usually still work, so you can typically drive carefully to a shop, but wheels can lock in a hard stop. If the ABS and red brake light are on together, stop driving and have it checked.

What Does the ABS Light Mean?

ABS stands for anti-lock braking system. When you brake hard, especially on wet or icy pavement, ABS rapidly pulses the brakes on any wheel that is about to lock up. That keeps the tires rolling just enough that you can still steer while you stop. You feel it as a buzzing or pulsing in the brake pedal.

The amber ABS light comes on for a second or two when you start the car as a self-test, then goes out. If it stays on while driving, the ABS computer has found a problem and has switched the anti-lock function off. It is not saying your brakes have failed. It is saying the backup safety system that prevents skids is not available right now.

For a full rundown of other symbols, see our dashboard warning lights guide.

Is It Safe to Drive With the ABS Light On?

In most cases, yes, carefully and for a short time. With only the ABS light on, your regular hydraulic brakes normally still work. The pedal should feel the same and the car should stop the same in normal driving.

What you lose is protection in a panic stop. Without ABS, a hard stop can lock the wheels, and locked front wheels mean the car will not turn no matter how you steer. That matters a lot on wet roads, in the first Philadelphia snow, or in sudden stop-and-go traffic on I-95. Until it is fixed:

  • Leave extra following distance.
  • Brake earlier and more gently.
  • In an emergency stop, if you feel the wheels lock, ease off slightly and reapply (the old-school way of braking without ABS).
  • Get it checked soon rather than living with it for months.

On many vehicles, the same fault also disables traction control and stability control, so you may see those lights too. Read more in our guide to the traction control light.

When the ABS and Brake Light Are On Together: Stop Driving

The red BRAKE light (or a circle with an exclamation point) is a different warning. It can mean the parking brake is on, the brake fluid is low, or there is a problem with the hydraulic system or brake force distribution. When the red brake light and the ABS light come on at the same time, the car may not be able to balance braking front to rear properly, and the problem may be more than an ABS fault.

If both lights are on, do not keep driving. First make sure the parking brake is fully released. If the lights stay on, the pedal feels soft or sinks, or the car takes longer to stop, pull over safely and have the car towed. AutoZmotive does not tow, but we can recommend a local towing company. See our brake warning signs article for other symptoms that mean stop now.

Common Causes of an ABS Light

  • Bad wheel speed sensor. Each wheel (or axle) has a sensor that tells the ABS computer how fast that wheel is spinning. These sit right behind the wheel, exposed to water, road salt, brake dust and pothole hits. A failed sensor is the most common cause.
  • Damaged sensor wiring or connector. The wires flex with the suspension and can chafe, corrode or get torn, especially after winter salt or a big pothole.
  • Damaged or dirty tone ring. The sensor reads a toothed or magnetic ring on the axle or hub. Rust, cracks or debris on that ring can cause bad readings. On some cars it is built into the wheel bearing.
  • Low brake fluid. Fluid drops as pads wear, and also when there is a leak. Some cars turn on the ABS light, the brake light, or both. Never just top it off and forget it: find out why it is low.
  • ABS module or pump problem. The control module and hydraulic unit can fail, often from internal electrical faults or corrosion. This is less common and more expensive.
  • Blown fuse or relay for the ABS pump or module.
  • Low system voltage. A weak battery or failing alternator can trigger ABS and other warning lights all at once.

How a Shop Diagnoses an ABS Light

A basic code reader from a parts store usually only reads engine codes, not ABS codes. ABS faults are stored in the ABS module and need a scan tool that can talk to that module. A technician will read the stored code (for example, a fault for a specific wheel speed sensor circuit), look at live wheel speed data while the car moves, and then test the sensor, wiring and tone ring to confirm the cause before replacing anything. Replacing a sensor based on the code alone sometimes misses a broken wire or a rusted tone ring.

How Much Does ABS Repair Cost?

Costs vary a lot by vehicle and by what failed. As a general guide for typical U.S. pricing (parts plus labor):

RepairTypical U.S. range
Wheel speed sensor replacementAbout $150 to $400 per sensor
Sensor wiring or connector repairAbout $100 to $300
Hub or wheel bearing with built-in tone ringAbout $250 to $700 per wheel
ABS module or hydraulic unitAbout $500 to $1,500 or more

These are broad ranges, not quotes. Always get a written estimate for your specific car.

Will an ABS Light Fail PA State Inspection?

It can. Pennsylvania requires an annual safety inspection, and the brake system is part of it. An illuminated ABS warning light on a vehicle equipped with ABS can cause the car to fail. If your inspection is coming up, get the light diagnosed first so you are not paying for a re-check. Our PA state inspection guide covers what else is checked.

Get Your ABS Light Checked in Northeast Philadelphia

AutoZmotive Repair Shop at 7929 Charles St in Holmesburg diagnoses ABS and brake warning lights and shows you photos or video of the problem before any work. You get a written estimate first, and repairs come with a 12-month / 12,000-mile parts and labor warranty. We also handle brake repair and PA state inspections. Book online or call (215) 565-0220.

Key Takeaways

  • →ABS light alone: normal brakes usually work, but anti-lock protection is off
  • →ABS light plus the red brake warning light together is a reason to stop driving
  • →A failed wheel speed sensor or damaged wiring is the most common cause
  • →Low brake fluid can point to worn pads or a leak and should never be ignored
  • →An illuminated ABS light can cause a car to fail Pennsylvania safety inspection

Common Questions

Can low brake fluid cause the ABS light to come on?

Yes, on some vehicles low brake fluid turns on the ABS light, the red brake light, or both. Low fluid usually means worn pads or a leak, so have the system inspected instead of just topping it off. If the pedal feels soft, do not drive the car.

Can I reset the ABS light myself?

Disconnecting the battery or clearing codes with a scan tool may turn the light off briefly, but if the fault is still there the light will come back, often within the first few miles. Clearing it does not fix anything. It is better to find and repair the actual cause.

Why does my ABS light come on and then go off?

An intermittent ABS light often points to a sensor or wiring problem that only shows up over bumps, in wet weather, or at certain speeds. A damaged connector or a sensor with debris on it are common culprits. The ABS module usually stores the code even after the light goes out, so a shop can still read it.

Does the ABS light affect traction control?

Usually, yes. Traction control and stability control rely on the same wheel speed sensors as ABS, so a fault that turns on the ABS light often turns on the traction control light too. Those systems will typically be disabled until the fault is repaired.

Will a bad battery turn on the ABS light?

It can. The ABS module needs steady voltage, and a weak battery or failing alternator can set ABS and several other warning lights at once. If many lights came on together, have the charging system tested first.

Evan

Owner and Lead Mechanic at AutoZmotive Repair Shop in Holmesburg, Philadelphia. Questions about this article? Get in touch.

Reviewed: November 2026

Ready to Get Your Car Fixed?

Call us today or stop by the shop. Walk-ins welcome, appointments preferred.

(215) 565-0220Book Online