Skip to main content
(215) 565-0220Mon–Fri: 8:30AM–5:30PM · Sat: 8:30AM–4PM
Noise When Turning the Steering Wheel? What It Means
Suspension

Noise When Turning the Steering Wheel? What It Means

November 1, 20265 min read
Written by Evan, Owner & Lead Mechanic
Back to all articles

Quick Answer

A clicking noise in tight turns is usually a worn outer CV joint. Clunking points to ball joints, tie rods, sway bar links, or strut mounts. Whining often means low power steering fluid or a failing pump. Groaning or creaking suggests dry ball joints or worn bushings, and humming that changes as you turn usually means a wheel bearing.

Why Does My Car Make a Noise When I Turn the Steering Wheel?

Turning puts extra load on your car’s steering, suspension, axles, and wheel bearings, so a part that’s starting to wear often makes its first noise in a turn. The type of noise, clicking, clunking, whining, groaning, or humming, and when you hear it are strong clues to the cause. Some of these are minor; others affect your ability to steer and stop safely. For a broader look at noises, see our guide to strange car noises.

Steering Noises at a Glance

NoiseWhen you hear itLikely causeSafety concern?
Clicking or poppingTight turns, acceleratingWorn outer CV jointYes, if ignored
ClunkingTurning, bumps, potholesBall joints, tie rods, sway bar links, struts/mountsYes for ball joints and tie rods
WhiningTurning the wheel, worst at full lockLow power steering fluid or pumpModerate
Groaning / creakingSlow turns, parking lots, bumpsDry ball joints, worn bushings, strut mountsModerate to yes
Humming / growlingChanges with speed and turningWheel bearingYes, if severe

Clicking Noise When Turning: Usually a CV Joint

A rhythmic clicking or popping noise when making sharp turns, especially while accelerating out of a parking spot or around a corner, is the classic sign of a worn outer CV (constant velocity) joint. CV joints sit at the ends of the axles that drive the front wheels on front-wheel-drive and many all-wheel-drive vehicles.

The usual root cause is a torn CV boot, the rubber cover that holds grease in and keeps dirt and water out. Once it tears, grease slings out (you may see dark grease on the inside of the wheel), and the joint wears quickly. If a torn boot is caught early, the boot can sometimes be replaced; once the joint clicks, the usual fix is a replacement axle. A CV joint that’s left to wear can eventually fail and leave the car unable to move. Learn more about our driveline service.

Clunking When Turning or Going Over Bumps

A clunk or knock usually means something in the suspension or steering has worn and developed play. Common causes:

  • Ball joints, the pivots that connect the control arms to the steering knuckles. Worn ball joints can clunk over bumps and in turns. A badly worn ball joint can separate, causing loss of control.
  • Tie rod ends, connect the steering rack to the wheels. Worn tie rods cause clunking, loose or wandering steering, and uneven tire wear. They’re a direct safety part of the steering.
  • Sway bar links, very common in Philadelphia given our potholes. They often clunk or rattle over bumps and are usually a less expensive repair.
  • Struts and strut mounts, a worn upper strut mount or bearing can clunk or pop when you turn the wheel, especially when parked or at low speed. See our article on shocks and struts replacement.

Whining Noise When Turning the Steering Wheel

A whine or squeal that gets louder as you turn the wheel, often worst when parking or at full lock, usually points to the hydraulic power steering system:

  • Low power steering fluid from a leak, check the reservoir level with the owner’s manual as your guide, and use only the fluid type it specifies.
  • A failing power steering pump, sometimes with heavier steering.
  • A slipping drive belt, which may squeal more than whine.

Many newer cars use electric power steering, which has no fluid. On those, a whine or a sudden heavy steering feel, often with a warning light, needs a diagnostic check. Driving with low fluid can damage the pump, and losing power assist makes steering much harder, so don’t put it off.

Groaning or Creaking When Turning

A groan or creak, especially during slow turns in parking lots or over speed bumps, often comes from dry or worn ball joints, worn control arm or sway bar bushings, or strut mounts. Rubber bushings dry out and crack with age, heat, and road salt. Some creaks are more annoying than dangerous, but a creaking ball joint can be an early sign of wear, so it’s worth a professional inspection rather than guessing.

Humming That Changes When You Turn: Wheel Bearing

A humming, growling, or roaring noise that rises with vehicle speed and gets louder or quieter as you gently swerve left and right usually means a worn wheel bearing. Because turning shifts the car’s weight, the noise often changes when the bad bearing is loaded or unloaded. It’s easy to confuse with tire noise, so an inspection with the car lifted helps confirm it. A badly worn bearing can overheat and, in extreme cases, affect the wheel’s attachment, so get it checked once you notice it.

Which Steering Noises Are a Safety Issue?

Get the car inspected promptly, and drive gently until then, if you notice any of these:

  • Clunking along with loose, wandering, or vague steering (possible ball joint or tie rod wear)
  • The steering wheel is off-center or the car pulls suddenly
  • Loud grinding or growling from a wheel
  • Steering that suddenly becomes very heavy
  • Clicking from a CV joint that’s getting louder

If the steering feels loose or unpredictable, don’t drive it on the highway. Have it inspected first.

Steering and Suspension Inspection in Northeast Philadelphia

AutoZmotive Repair Shop at 7929 Charles St in Holmesburg can find the source of a steering noise, show you photos or video of any worn parts, and give you a written estimate before any work. Repairs are covered by our 12-month / 12,000-mile parts and labor warranty. Call (215) 565-0220, text (215) 978-7049, or book an appointment. Learn more about our suspension service.

Key Takeaways

  • →Clicking in tight, slow turns is the classic sign of a worn outer CV joint, often with a torn boot
  • →Clunking over bumps or while turning points to worn suspension or steering parts
  • →Whining that gets louder as you turn the wheel usually means low power steering fluid or a failing pump
  • →Humming that changes when you swerve left or right is a common wheel bearing clue
  • →Worn ball joints and tie rods are a safety issue, they can affect steering control

Common Questions

Is it safe to drive with a clicking CV joint?

You can usually drive a short time with a mildly clicking CV joint, but it will keep getting worse. If it fails completely, the car can lose drive to that wheel and be stranded. Have it replaced soon, especially if the clicking gets louder.

Why does my steering wheel make noise when I turn it while parked?

Noise when turning while stopped is often from the power steering system, such as low fluid or a pump, or from worn upper strut mounts. A groan from dry ball joints is also possible. A quick inspection can tell which one it is.

How do I check my power steering fluid?

With the engine off, find the power steering reservoir (your owner’s manual shows where) and check the level against the marks. Use only the fluid type your manual specifies. If your car has electric power steering, there is no fluid to check.

How can I tell a wheel bearing noise from tire noise?

Wheel bearing noise usually gets louder or quieter as you gently swerve left and right at speed, while tire noise tends to stay the same and changes with road surface. A technician can confirm by checking the wheel for play and roughness with the car lifted.

Can potholes cause steering noises?

Yes. Hard pothole hits can damage sway bar links, ball joints, tie rods, struts, and wheel bearings, all of which can make noise when turning. If a new noise starts after a pothole, have the suspension checked.

Evan

Owner and Lead Mechanic at AutoZmotive Repair Shop in Holmesburg, Philadelphia. Questions about this article? Get in touch.

Reviewed: November 2026

Ready to Get Your Car Fixed?

Call us today or stop by the shop. Walk-ins welcome, appointments preferred.

(215) 565-0220Book Online